Replacement Spikes for Ice Cleats: When to Swap Them and How
Learn when replacement spikes for ice cleats are worth buying, how to spot worn studs, and how to swap them so your traction holds on winter ice.
Updated November 2026
Replacement spikes for ice cleats are worth buying once the existing studs are worn down, bent, or missing. Most spikes wear smooth on the tip after a season of pavement walking, and smooth spikes lose their bite on packed snow and glaze ice. Swapping only the damaged studs, instead of the whole cleat, is usually the cheapest way to get your grip back.
Why ice cleat spikes wear out
Spikes are typically made of hardened steel or tungsten carbide, but they still wear. Asphalt, concrete and salted sidewalks grind the tips down, and every step that lands on bare pavement takes off a little more. Frequent walking on pavement, rather than snow, is the main reason spikes dull faster than owners expect.
Shopping for one? See our guide: Microspikes vs Ice Cleats (2026): Which Is Better for Winter Walking?.
Corrosion matters too. Road salt gets into threads and cores, and moisture that freezes and thaws can loosen a stud over time. A spike that wiggles in its housing is no longer transferring force to the ice, so it stops gripping even if the tip looks fine.
What to check before you buy
Look at each spike and ask three questions. Is the tip flattened or rounded? Is the stud bent or leaning? Does it rotate or rock when you press on it? If you answer yes to any of these, replacement is the right call. If the tips are simply dull but still sharp at the point, a stiff wire brush and some cleaning may restore enough bite for another season.
Check the thread size and length before ordering. Spikes are not universal, and a stud that is too long can stop the cleat from sitting flat on the sole. Measure the old spike with a caliper or ruler, and note the thread pattern on the housing. If you are unsure which fit your boots, our guide on Ice Cleats Size Chart: How to Pick the Right Fit for Your Boots walks through sizing.
How to replace the spikes
- Clean the cleat thoroughly, removing salt, grit and dried mud from the threads and housing.
- Remove the worn spike with pliers or the tool supplied with the cleat. Turn slowly to avoid stripping the threads.
- Check the housing for cracks or stripped threads. A damaged housing will not hold a new spike securely.
- Apply a small amount of thread-locking compound if the manufacturer recommends it, then thread in the new spike by hand until snug.
- Tighten with the proper tool, but do not overtighten. Test the spike by pressing on it. It should feel firmly locked.
Manufacturers commonly advise replacing spikes in sets rather than singly, so both boots or both cleats wear evenly. Mismatched wear can make one side slip before the other.
Tips to make spikes last longer
- Remove cleats before walking on indoor floors or dry pavement for long stretches.
- Rinse off road salt after each use to slow corrosion.
- Dry cleats fully before storing them, and keep them away from heat sources.
- Inspect spikes every few weeks during the season, not just at the start.
What we’d use
For a straightforward swap that fits common rubber-and-steel cleats, a replacement stud kit from a known cleat maker is the simplest choice. Search for View on Amazon and confirm the thread size against your old spikes before buying.
If you want a full cleat that you can service yourself over several seasons, consider a model with easily replaced studs, such as those covered in Traction Cleats Ice Snow Grips: Which Ones Work and How to Choose (2026). Search for View on Amazon to compare options.
FAQ
How often should I replace ice cleat spikes?
There is no fixed schedule. Replace them when the tips are flattened, the studs are bent, or they wobble in the housing. Heavy pavement use can wear spikes out in a single season.
Can I use any spike on my cleats?
Not always. Thread size, length and housing design vary by brand. Match the spike to the manufacturer’s specifications or to the exact thread pattern of your old spike.
Are replacement spikes safe to install at home?
For most cleats, yes, with basic hand tools. If the housing is cracked or the threads are stripped, have a repair shop or the manufacturer assess the cleat before you continue wearing it, since a loose spike can fail on ice.
Related reading
- Ice Cleats for Metal Roof: How to Choose and Install Them Safely
- Ice Cleats for High Heels: Do They Work and How to Choose
- Why Does My Ice Scraper Scratch Paint? Causes and Fixes
- What Is a Good Alternative for Ice Scraper? 5 Options That Work
Ready to choose one?
