We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

How to Put On HT All Purpose Ice Cleats: A Step-by-Step Guide

Learn how to put on HT all purpose ice cleats in a few minutes, with tips for a snug fit, safe walking, and taking them off without damage.

Updated November 2026

Putting on HT all purpose ice cleats takes about two minutes once you know the routine. The key is to fit the cleat over the sole, position the stretch rubber so it sits evenly, and tighten it so the traction bars grip without slipping. Get that right and you’ll have reliable footing on icy sidewalks, driveways and trails.

Before You Start

Check that your cleats are the right size for your shoe before you begin. A cleat that is too small will stretch tight and tear, while one that is too large will shift under your foot. Most HT all purpose cleats are sold in size ranges that match standard men’s and women’s shoe sizes, so confirm the size chart printed on the packaging. Also make sure your shoe soles are clean and dry, since mud or grit can keep the cleat from seating flat.

Shopping for one? See our guide: Microspikes vs Ice Cleats (2026): Which Is Better for Winter Walking?.

Step-by-Step: Installing the Cleats

  1. Lay the cleat flat. Turn the cleat so the rubber harness faces up and the metal traction coils or bars point down.
  2. Start at the heel. Pull the heel loop open and slide your heel into the back of the cleat, keeping the metal side flat against the sole.
  3. Stretch the harness over the toe. Pull the rubber strap forward and over the front of your shoe. Work it gradually so it does not snap back.
  4. Center the cleat. Make sure the traction section sits under the ball of your foot and extends evenly on both sides. A cleat that sits off-center will wobble on ice.
  5. Secure the sides. Pull the side straps or loops snugly so the cleat grips the shoe at the heel and along the sides. The fit should feel firm, not pinching.
  6. Test your footing. Stand on a flat, non-icy surface and rock forward and back. The cleat should not slide, and your toes should not feel crushed.

Checking the Fit and Adjusting

A good fit feels secure at the heel and toe, with the traction bars sitting firmly against the sole. Walk a few steps on a hard floor and listen for any clicking or slipping. If the cleat rides forward, retighten the heel loop. If it pinches the top of your foot, loosen the front strap slightly. Re-check after your first short walk outdoors, because the rubber can settle once it has been stretched.

Taking Them Off Without Damage

Remove the cleats by reversing the steps. Loosen the side straps first, then stretch the front harness up and away from the toe, and finally slide the heel out. Pulling only on the traction coils can bend them or tear the rubber, so always work from the harness. Store them somewhere dry so the metal does not rust between uses.

Common Mistakes

  • Forcing a cleat on a sole that is wet or caked with salt, which prevents a flat fit.
  • Stretching the harness too hard in one pull, which can tear the rubber.
  • Wearing cleats that are too tight, which restricts circulation and makes the fit uncomfortable.
  • Walking on hard bare floors indoors, which can wear down the traction coils.
  • Skipping the fit test before heading out on an icy surface.

A few supplies can make putting on and maintaining your cleats easier. A basic set of gripping tools helps when the rubber is stiff in cold weather.

  • Cold-weather rubber gloves: Give you a firm grip on stretch harnesses when your fingers are cold. View on Amazon
  • Shoe storage bag: Keeps cleats dry and prevents rust when they are not in use. View on Amazon

FAQ

Do I need to take my shoes off to put on HT all purpose ice cleats?

No. You can install them with your shoes on, since the heel loop and front harness are designed to fit over footwear. Sitting down on a bench makes the process easier.

Why do my cleats keep slipping off my shoes?

Slipping usually means the cleat is too large or the harness is not tight enough. Re-check the size chart and tighten the heel loop and side straps until the fit feels secure.

Can I wear HT all purpose ice cleats in very cold temperatures?

The rubber can become stiff in extreme cold, so stretch it gently and allow a few minutes indoors for it to warm up. If you have concerns about footwear for medical conditions such as circulation problems, consult a healthcare professional.

Conclusion

Installing HT all purpose ice cleats comes down to sizing correctly, seating the cleat flat at the heel, and centering the traction under the ball of your foot. Test the fit on a flat surface before going outdoors. For more on choosing the right pair, see Ice Cleats Size Chart: How to Pick the Right Fit for Your Boots and Traction Cleats Ice Snow Grips: Which Ones Work and How to Choose (2026).

Colin Foster

About Colin Foster

Colin Foster is part of our editorial team and reviews and edits our everyday winter gear guides, checking product details against manufacturer specifications and owner feedback.

About the author

Colin Foster
Colin Foster

Colin Foster writes reviews and buying guides for Snow Crystals.